Calcium fluoride ball flap belt dryer

Under the continuous high requirements of the market for equipment quality, and in the contemporary era that pays attention to environmental protection, GRIFFIN Dryer enterprise selection recommends calcium fluoride ball flap Belt Dryer. Technical personnel and senior management personnel, and has a group of sophisticated production personnel. Their capabilities in research, design, service, etc., they have devoted themselves to research over the years, summed up again and again in practice, and have a deep understanding that "God rewards hard work" is a strong guarantee for the quality of customers' products!

Calcium fluoride is an inorganic compound that is colorless crystals or white powder. It is insoluble in water, slightly soluble in inorganic acid, and reacts with hot concentrated sulfuric acid to generate hydrofluoric acid. Calcium fluoride is generally prepared by the action of calcium carbonate and hydrofluoric acid or by repeatedly treating fluorite powder with concentrated hydrochloric acid or hydrofluoric acid. The natural calcium fluoride mineral is fluorite or fluorite, which is often gray, yellow, green, purple and other colors, sometimes colorless, transparent, vitreous, brittle, and has obvious fluorescence phenomenon. Very pure fluorspar is used to make specialty lenses. Fluorite is mainly used as a flux for metal smelting; when drinking water contains 1-1.5ppm calcium fluoride, it can prevent and treat dental diseases.

Calcium fluoride ball flap belt dryer, why is the flap belt dryer called flap?

Because the flap running in the box walks to the head or tail of the machine, it will turn over automatically, that is, it will run back and forth twice on the same floor, while the Mesh Belt Dryer will only run once. If they are all four-layer dryers, the flap of the flap dryer will run and dry eight times in the box, while the mesh belt of the mesh belt dryer will only run and dry four times in the box. The drying efficiency of the dryer is greater than that of the mesh belt dryer. The flap dryer is a kind of Drying Equipment for batch and continuous production. It uses steel chain plates as conveyor belts to carry materials for continuous drying. The flip dryer is suitable for goose egg pellets, various metallurgical mineral powder pellets, oxide skins, sludge balls, briquette, coke powder balls, desulfurized gypsum, slag-returning balls, etc. produced by the briquetting machine. Wide, high efficiency, energy saving and so on.


Our company developed calcium fluoride ball flap belt dryer features:

1. The guide rail is optimized according to the characteristics of Wuke, which can ensure its linear reading and writing strength, and the running resistance of the sprocket is small. The flipping mechanism completed by the guide rail is a unique structure of our company, which can ensure that the grid plate can be tilted freely.

2. The sprocket adopts automatic tensioning device, the chain plate runs smoothly, and the good guide rail can effectively solve the phenomenon of chain drop, chain jam, deviation and so on.

3. The grid plate is made of heat-resistant steel and punched into a mesh shape, which has high strength, is not easy to deform, and has good air permeability. The two sides of the grid are connected to the chain rollers. The unique grid structure of our company can ensure that the rollers on both sides are coaxial and easy to disassemble and install.

4. The chain plate adopts electromagnetic speed regulation or frequency conversion speed regulation transmission according to the characteristics of the working conditions, and the running speed can be adjusted according to the needs, and the drying time can be controlled.

5. Equipped with fire protection devices, the kiln head, kiln middle and kiln tail are equipped with temperature measuring devices and digital display, which is convenient to grasp and control the temperature in the kiln. The air inlet of the flue is designed with a smoke gate. Immediately cut off the heat source to prevent fire.

6. According to the initial moisture of the material and the characteristics of the material, the upper air or interlayer air distribution is adopted, the hot air is evenly distributed, and the cracking and bursting of the briquette due to rapid heating are effectively prevented, thereby improving the quality of the briquette and reducing the damage.

7. Our company reasonably chooses negative pressure induced air or positive pressure blast according to the material moisture and hot air temperature, which is also the result of GRIFFIN's years of practice.

8. Equipment failure. The lower part of the equipment is equipped with special cleaning equipment, and the dust particles are exported, thereby reducing the operation intensity and equipment failure.